Σπορ‪» Σκι‪» Σκι αντοχής‪» Ski waxes και ski service‪» Κεριά βάσης‪»

Start BW Base Wax 90 g

Start BW Base Wax 90 g


Τιμή
11,90 + κόστη παράδοσης
132,22 € / kg
Συμπ. ΦΠΑ 25.5 %


Ποσότητα
τμχ.



Κατάστημα (Helsinki)στο ράφι0 τμχ.
Άμεσα διαθέσιμα στο ηλεκτρονικό κατάστημα0 τμχ.


Η μέγιστη ποσότητα του προϊόντος που μπορείτε να παραγγείλετε είναι αυτή που έχουμε σε απόθεμα.
Διαθεσιμότητα
Αυτό το προϊόν δεν είναι προς πώληση αυτή τη στιγμή.

Λεπτομερής διαθεσιμότητα


Αξιολογήσεις
Συνολική βαθμολογία ()


Περιγραφή προϊόντος
Thorough base waxing is essential for successful ski waxing. A wax used for base waxing should be absorbed thoroughly onto the base and create a strong surface for waxes to be melted on top of it. Base waxing should be done always before using new skis and once a year to old skis.

Base waxing is for the glide zones of the base. Grip zone will be left without base waxing. Make sure that your skis do not have any defaults before you start using them. Clean up the glide zones of the base with polishing fibre that has been moisten with ski wax remover liquid. You can also clean up the glide zones of the base first absorbing with an iron a thick layer of base wax and then remove still warm and liquid wax by using a cloth. The melted liquid wax will absorb all dirt and move over to the cloth.

Polyethelen Bases A.K.A transparent bases:
1. Melt BW base wax onto the base. Let the wax cool down and scrape off the excess wax with a sharp acryl scraper. Repeat the procedure two or three times.
2. Melt glide wax to the base according to the weather. Let the wax cool down and scrape off the excess wax. Lastly brush the base with a brass brush until the base structure becomes visible. Repeat the procedure once or twice.
Your skis are now ready to use.
Note! When melting the wax, make sure no smoke comes out because if the iron is too hot it can damage the base.

Graphitele polyethelen bases a.k.a black bases
1. Melt BW base wax onto the base. Let the wax cool down and scrape off the excess wax with a sharp acryl scraper. Repeat the procedure once or twice.
2. Melt BWG base graphite wax onto the base. Scrape off immediately the excess wax with a sharp acryl scraper while the wax is still warm. Repeat the procedure once or twice.
3. Melt glide wax to the base according to the weather. Let the wax cool down and scrape off the excess wax. Lastly brush the base with a brass brush until the base structure becomes visible. Repeat the procedure once or twice.
Your skis are now ready to use.

Note! When melting the wax, make sure no smoke comes out because if the iron is too hot it can damage the base.




Βάρος
0,09 kg
(με το πακέτο πωλήσεων 0,12 kg)


Χώρα προέλευσης
Φινλανδία


Σχόλια
Προσθήκη σχολίου

Μάρκα